answersLogoWhite

0

Buick Lacrosse

The Buick LaCrosse is a mid-size luxury car manufactured by General Motors from September 2004 to the present. Two generations of this car have been produced; both are offered as a four-door sedan.

500 Questions

How do you replace low beam headlight on Buick lacrosse?

User Avatar

Asked by Wiki User

The procedure to replace head light assembly on buick lacrosse is as follows:---

The bright light fitting is the same as the dim so take it apart fist to see how the cover screws off/on and the light comes out. Both the cover and the bulb are removed by a standard twist to the counterclockwise and replaced by a twist to the clockwise.

Now to the dim light. You have to release the entire light assembly before you can remove the screw-on cover to reach the light.

On the rear edge of the light unit closest to the engine is a white locking tab. Pull that tab up just to the point where it releases…pull too far and it locks again.

Next, locate the other locking bracket which is a metal bracket in the center-rear of the light assembly. This bracket is held down by a screw. Remove the screw with a 10mm wrench. Lift the bracket just like you did the white bracket.

You should now be able to pull (or pry) the entire light unit forward a little. Depending on the size of your hands this might be enough.

If not, then you need to release the plastic bumper assembly to give you a little more space. This is done by removing two expansion locking pins, one that holds the little plastic strip down between the bright and dim lights and one that is located inside a rubber bumper on the engine side of the light unit.

To remove these locking pins, pull or pry up the little tab in the center of the pin just like you were pulling a nail by the head. That should give you a little more space.

. Note:-- The turn signal is part of the headlight assembly on your 2005 Buick LaCross.

How do you replace 2006 Cobalt rear turn signal bulb?

User Avatar

Asked by Wiki User

Inside the trunk, on either side you will find a velcroed trap door. Pull this open and inside you will see two locking tabs that hold the black plastic mounting for all of the lights inside the rear lens, remove the connector at the bottom by wiggling it back and forth until it disengages. Then remove the mounting by squeezing the protruding tabs towards the cennter, replace the bulb, reseat the mounting and reconnect the bottom electrical connector.

Where is the fuel filter located on a 2007 Buick Lacrosse CX?

User Avatar

Asked by Wiki User

At the rear f the vehicle, between the frame rails.

How do you reset oil change light on a 2009 Buick Lacrosse?

User Avatar

Asked by Wiki User

On the left side of the steering wheel use the toggle button to scroll to the settings menu. Press the > button to go to Vehicle Settings. Press > again and scroll to Vehicle. Press > once again and scroll to Oil Life Reset. You can set to any percentage you want from 10-100%. Press and hold the OK button to set.

What is the maximum towing capacity of the 2008 Buick LaCrosse?

User Avatar

Asked by Wiki User

The maximum tosing capacity of the 2008 Buick LaCrosse is 1000 lbs..

What causes a abs light to come on?

User Avatar

Asked by Wiki User

most of the time your pads are about gone

Where is the fuse box on 2006 on Buick Lacrosse?

User Avatar

Asked by Wiki User

There are two fuse blocks in the 2006 LaCrosse. one is located on the passenger side under the hood in a black colored box. The other is inside the passenger side when you open the door.

Where is the fusebox on 2006 Buick lacrosse?

User Avatar

Asked by Wiki User

I own a Buick 2003 Lasaber and mine is under the back seat, so is my Battery, it lifts up if you push in and pull up at the same time. Hope this helps.

How do you Program homelink?

User Avatar

Asked by Wiki User

Programming Homelink is very easy. If you have access to the internet, simply visit the general homelink training page and watch the video (http://www.homelink.com/training/video.tml). These instructions are applicable to any Homelink vehicle system. (A simple way to do this without watching the video is to just push the "learn" button on the back of your garage door opener main box and then push and hold--just a few seconds--whichever Homelink button you want it to recognize. Usually your garage door opener main box will beep or flash when it has recognized the signal.) +++++++++++++++++++++++++++++ Would like to add that for certain models (I have Craftsman) you need to have a programmed remote from which the homelink system can learn. You need to press buttons 1 and 3 on the homelink for about 20 seconds which puts it in the learn mode. Then press the button that needs to be programmed while pressing the button on the handheld remote. The garage door will open/ close due to this. The light will first flash slowly and then rapidly in the homelink system. If it still doesnt work, the next step is to press the learn button in the main unit and then press the same homelink button in the car for about 2 seconds a couple of times. I have also noticed that the handheld remote needs to be placed really close for the system to learn (during the initial learn mode) and you may need to try different angles.

What does the On Star Safe and Sound Plan include?

User Avatar

Asked by Wiki User

Go to ONStar.com and they clearly list what you get with each plan. Basically it includes all the goodies except for navigation.

Is the 2010 Buick LaCrosse electric or gas?

User Avatar

Asked by Wiki User

The 2010 Buick LaCrosse is a gas-powered vehicle.

Who is the current Buick spokesman?

User Avatar

Asked by Wiki User

Vinnie Deegan

What are the size of windshield wipers of a 2010 Buick lacrosse?

User Avatar

Asked by Wiki User

The 2010 Buick LaCrosse takes 26" drivers side and 18" passenger side wiper blades. See related links below. Length is not the only issue when purchasing wiper blades, so is attachment. Always lookup exact wiper blade part numbers by vehicle make, model and year.